Marvel 6CADM Guia de Resolução de Problemas descarregar pdf (Página 7)

USING YOUR MICROSENTRY™ REFRIGERATOR CONTROL

During inial startup, or anyme power is interrupted, there will

be an approximate 5 minute delay before the refrigerator starts.

During this period the controller will be assessing the tempera-

ture in the refrigerator and the display will appear errac, this is

normal. The desired set temperature can be programmed during

this start up period.

Starng your refrigerator

The refrigerator will begin start up when inially plugged in or

when power resumes aer a power outage. At this me the re-

frigerator will take approximately 5 minutes to begin running as

noted above. If the refrigerator has been turned o during use,

“OFF” will appear on the display. To start the refrigerator from

the “OFF” posion press and hold the ON/OFF buon for three

seconds.

Set temperature

To set the set temperature, press and connue to hold “SET”

buon. Aer one second, set temperature will be displayed.

While holding “SET” buon use the “WARMER” or “COLDER”

buon to desired set temperature.

NOTE: Momentarily pressing & releasing “SET” buon will access

informaon menu of control. Refer to appendix A for informaon

on this feature.

Refrigerator operaon

The available temperature range of the refrigerator is 1° to 7° C.

It may take up to 24 hours for your refrigerator to reach desired

temperature. This will depend on amount of contents loaded

and number of openings and closings of the door.

For best results allow refrigerator to “pull down” to desired set

temperature before loading. Once contents are loaded, allow

at least 48 hours for temperature to stabilize before making any

adjustments to the set temperature.

Alarms

Your MicroSentry™ refrigerator control will monitor refrigerator

funcon and alert you with a series of audible and visual alarms.

For all alarm and error codes, the alarm LED located in the top

le corner of the display panel will illuminate a steady amber.

For all alarm and error codes except condenser cleaning, an au-

dible alarm will sound, beeping in one (1) second intervals.

• Door Ajar Alarm: If the door has been le

open for over ve (5) minutes, the alarm will sound

and the display panel will ash “do.” The alarm will

stop once the door has been closed.

• High and Low Temperature Alarm: If your unit

reaches an unacceptable temperature, above or be-

low your set temperature for too long, the tempera-

ture alarm will sound in one (1) second intervals.

The display panel will ash either “hi” or “Lo” de-

pending upon the condion. “hi” indicates a high temperature

alarm, and “Lo” indicates a low temperature alarm. How far

the temperature must deviate above or below set temperature,

and for how long the temperature must remain there before the

temperature alarm is triggered is fully customizable. See Appen-

dix A for details on how to congure the alarm.

• Temperature Sensor Fault: If the control

detects that the temperature sensor is not properly

funconing, an audible alarm will sound, and “E1”

will ash on the display. Please call AGA MARVEL customer ser-

vice or your dealer if this error code is displayed.

• Condenser Needs Cleaning: When the refrig-

erator has reached the recommended amount of run

me for a condenser cleaning, “cL” will ash on the

display as a reminder to clean the condenser. No audible alarm

is associated with the condenser clean warning. To clear the

alarm:

1) Press and quickly release the SET key 7 mes.

“cnd” will be displayed on the screen.

2) While “cnd” is displayed, press and hold the SET key.

The display will show the number of weeks the con-

denser has been operang.

3) Connue to hold the SET key, then press and release the

ON/OFF key. The number shown on the display will be

reset to 00.

4) Release the SET key.

5) The display will return to normal operaon aer a few

seconds with no key presses.

See the detailed owner’s reference guide for further details.

NOTE

Figure 7

Press and Hold Press and Hold

Set Colder

Warmer ON/OFF

Alarm

Door Switch

Control

NOTE

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comentários a estes Manuais

Sem comentários

Marvel 6CADM Guia de Resolução de Problemas Página 7

Comentários a estes Manuais

Manuais e produtos relacionados com não Marvel 6CADM